Eric Cayeux

Eric Cayeux

Sjefsforsker
Telefon: +47 51 87 50 07
Mobil: +47 475 01 787
Epost: erca@norceresearch.no
Kontoradresse: Prof. Olav Hanssensvei 15, 4021 Stavanger, Norway

Aktuelt

Eric cayeux
Nyhet
29. mai 2020

Stor praktisk verdi i oljeindustrien

Prosjekter

Bore2
Prosjekt

6n Degrees of Freedom Transient Torque & Drag
Digiwell tilpasset
Prosjekt

DigiWells: Digitalt brønnsenter for verdiskaping, konkurranseevne og minimalt miljøavtrykk
Prosjekt

DrillWell - Drilling and Well Centre for Improved Recovery

Publikasjoner

Analysis of Torsional Stick-Slip Situations Observed with Downhole High-Frequency Magnetometer Data
2020
An Approach to Autonomous Drilling
2020
Time, Pressure and Temperature Dependent Rheological Properties of Drilling Fluids and their Automatic Measurements
2020
Measurement of the Flowrate Out of a Well for Conventional Drilling Operations
2020
Digitalization of Detailed Drilling Operation Plans and Verification of Automatic Progress Tracking with an Online Drilling Simulator Environment
2020
Toward Seamless Interoperability between Real-Time Drilling Management and Control Applications
2019
Effect of Solid Particle Concentration on Drilling Fluid Rheological Behavior and its Impact on Pressure Losses
2019
Modelling of the movement of a prolate particle in the steady state flow of a non-newtonian fluid in an inclined annulus with inner string rotation
2019
On the importance of the coupling between transient mechanical, hydraulic and thermal effects for the modelling of real-time drilling operations
2019
Reconstruction of Pipe Movement from Downhole High Frequency Measurements
2019
Measurement of Drilling Fluid Rheology and Modeling of Thixotropic Behavior
Applied Rheology 2019
Modelling of Drilling Fluid Thixotropy
2018
Drill-string dynamics in deviated wells in the presence of heave
2018
SPE-191339-MS Analysis of Asymmetric Too.-Joint Wear while Drilling Long Horizontal Sections
2018
IADC/SPE-189642-MS On the Importance of Boundary Conditions for Real-Time Transient Drill-String Mechanical Estimations
2018
Recontruction of Pipe Displacement Based on High-Frequency Triaxial Accelerometer Measurements
2018
Automatic risk uncertainty estimation to support decision making during drilling operation planning: Case study on an ERD well
Oil, Gas 2017
Challenges in the Automation of a Laboratory-Scale Drilling Rig and Comparison with the Requirements for Full Scale Drilling Automation
2017
Challenges and Solutions to the Correct Interpretation of Drilling Friction Tests
2017
Use of Quantitative Risk Analysis Methods to Determine the Expected Drilling Parameter Operating Window Prior to Operation Start: Example From Two Wells in the North Sea
2017
Modelling of the Dynamic Behavior of the Power Tansmission of an Automatic Small Scale Drilling Rig
2017
From shallow horizontal drilling to ERD wells: How scale affects drillability and the management of drilling incidents
Journal of Petroleum Science and Engineering 2017
A Novel Method for Locally Updating an Earth Model While Geosteering
International journal of geosciences 2017
Insights Into the Physical Phenomena That Influence Automatic Gain/Loss Detection During Drilling Operations
SPE Drilling & Completion 2016
Use of a Transient Cuttings Transport Model in the Planning, Monitoring and Post Analysis of Complex Drilling Operations in the North Sea
2016
Long Reach Well Concept
2016
Accuracy and Correction of Hook Load Measurements During Drilling Operations
2015
Principles and Sensitivity Analysis of Automatic Calibration of MPD Methods Based on Dual-Gradient Drilling Solutions
2014
Estimation of Weight and Torque on Bit: Assessment of Uncertainties, Correction and Calibration Methods
2014
Mathematical Modeling of Drilling Operations by Use of Nitrogen-Enriched Mud: A Case Study by Use of a Recorded Drilling Data-Set
SPE Drilling & Completion 2014
Toward Drilling Automation: On the Necessity of Using Sensors That Relate to Physical Models
SPE Drilling & Completion 2014
Real-Time Evaluation of Hole-Cleaning Conditions With a Transient Cuttings-Transport Model
SPE Drilling & Completion 2014
Real-Time Evaluation of Hole Cleaning Conditions Using a Transient Cuttings Transport Model
2013
A strategy for Effective Loccal Updates of the Geological Structure in an Earth Model during Drilling
2012
Advanced Drilling Simulation Environment for Testing New Drilling Automation Techniques and Practices
SPE Drilling & Completion 2012
Early symptom detection based on real-time evaluation of downhole conditions: principles and results from several North Sea drilling operations
SPE Drilling & Completion 2012
From Machine Control to Drilling Control On the Necessity of Sensors which Relates to Physical Models
IEEE Instrumentation and Measurement Technology Conference. Proceedings 2012
Automation of Drawworks and Topdrive Management to Minimize Swab/Surge and Poor-Downhole-Condition Effects
SPE Drilling & Completion 2011
Automation of Mud-Pump Management: Application to Drilling Operations in the North Sea
SPE Drilling & Completion 2011
Real-Time Optimization of the Drilling Process - Challenges in Industrialization
2009
Offshore Field Test of a New System for Model Integrated Closed-Loop Drilling Control
SPE Drilling & Completion 2009